Yale Little Mule® LMG Cable Grip

Little Mule® LMG Series | Wire Rope & Cable Grip | 2000–5000 daN Pulling Force | Parallel Jaw

The LITTLE MULE® LMG cable grip is a device for gripping, pulling and tensioning uncoated wire ropes, cables and metal rods up to 1770 N/mm² tensile strength (1960 N/mm² with the LMG II-X grooved jaws variant), with pulling force ratings from 2000 to 5000 daN covering common cable installation and tensioning tasks. The parallel jaw design provides a firm, non-slip grip without damaging the rope, while a spring-loaded guide prevents the grip dropping off and allows instant release without jamming. Note: the LMG is a gripping device for pulling — it is not a lifting device.

Key Features

• 2000–5000 daN pull force — Three core ratings plus the LMG II-X high-tensile variant.
• Parallel jaw grip — Firm non-slip engagement that distributes force evenly to protect the cable surface.
• Spring-loaded guide — Prevents the grip from dropping off the rope and allows instant clean release.
• Smooth or grooved jaws — Standard LMG for ropes to 1770 N/mm²; LMG II-X grooved jaws for ropes to 1960 N/mm².
• Wide application range — Suitable for uncoated wire rope, cable and round metal rod.
• Robust forged construction — Long service life under repeated tensioning cycles.
• Tool-free attachment — Spring action releases the jaws for fast attachment to the cable.
• Used with wire rope pullers — Pairs with the Yaletrac and similar wire rope pullers for cable installation tasks.

Technical Specifications

Rated in daN pull force, NOT kg lifting capacity. The LMG is designed for gripping cables under tension during pulling and stringing operations — not as a lifting attachment. The LMG II-X variant is supplied with grooved jaws specifically for higher-tensile-strength wire ropes (up to 1960 N/mm²).

More About This Product

The LITTLE MULE® LMG cable grip is a device for gripping, pulling and tensioning uncoated wire ropes, cables and metal rods up to 1770 N/mm² tensile strength (1960 N/mm² with the LMG II-X grooved jaws variant). Pulling force ratings from 2000 to 5000 daN cover common cable installation and tensioning tasks. The parallel jaw design provides a firm, non-slip grip without damaging the wire rope, while a spring-loaded guide prevents the grip from dropping off the rope and allows instant release without jamming. Note: The LMG is a gripping device for pulling — it is not a lifting device.

Suitable Applications

Overhead power line installation, telecoms cable stringing, suspension bridge cable tensioning, wire rope drag-in operations, conductor pulling, structural cable installation, and any cable or rope pulling operation requiring a temporary high-force grip.

How to Use the LMG Cable Grip

1. Inspect the LMG before every use — body, jaws, spring, pivot points and identification marks.
2. Confirm cable diameter and tensile strength are within the rated range for the selected LMG model.
3. Operate the spring-loaded guide to open the jaws.
4. Position the LMG on the cable at the desired grip point.
5. Release the spring guide to engage the parallel jaws.
6. Connect the LMG attachment eye to the wire rope puller or rigging assembly.
7. Apply tension — the jaws self-tighten under load to grip the cable.
8. After use, release tension before opening the jaws to remove from the cable.

Warning:
The LMG is a CABLE GRIP for pulling — it is NOT a lifting device and must not be used to suspend loads overhead. Confirm cable tensile strength is within the rated range — use LMG II-X for high-tensile ropes up to 1960 N/mm². Never exceed the rated pull force. Inspect jaws for wear or damage before every use; worn jaws can slip under load.

Safety Information

• Never exceed the rated working load limit (WLL) displayed on the equipment.
• Never use the equipment if any component shows visible damage, wear or deformation.
• Keep all personnel clear of the lifted load at all times.
• Do not modify, repair or substitute components other than as specified by the manufacturer.
• Ensure the operator is trained, competent and authorised for the lifting operation.
• Do not shock load the equipment under any circumstances.

Inspection and Maintenance

Inspect before each use — focus on all load-bearing components, welds, hooks, safety latches, chain, rope and pendant controls. Thorough examination under LOLER 1998 is required at intervals not exceeding 6 months by a competent person. Replacement parts must be genuine manufacturer items to maintain certification. Records of all inspections must be retained for the life of the equipment.

Frequently Asked Questions