The STAHL CraneSystems STD is an off-standard development of the ST electric chain hoist for long goods and loads that must be picked up at two points.
It has two load chains driven in sync by a single hoist motor, so both hooks lift and travel together and the load cannot tilt dangerously.
The distance between the hooks is chosen to suit the material, and the hoist is built to the width of your load.
Thanks to its low headroom it also suits low buildings and achieves maximum hook paths. This is an enquiry-only product: tell us about the load and we will specify and quote it.
The STD is built from the ST chain hoist programme, which covers these frame sizes:
| Frame | Load capacity range | Note |
|---|---|---|
| ST 05 | 125 to 630 kg | |
| ST 10 | 500 to 1,000 kg | |
| ST 20 | 1,000 to 2,000 kg | |
| ST 30 | 1,250 to 3,200 kg | |
| ST 32 | 1,250 to 3,200 kg | |
| ST 50 | 2,500 to 5,000 kg | Some trolley options 1/1 reeving only in the standard range |
| ST 60 | 3,200 to 6,300 kg | Some trolley options 1/1 reeving only in the standard range |
Capacity, hook spacing, lifting speed and lift height are set to your load and building. Standard supply 380 to 415 V 50 Hz, pole-changing hoist motor 1:4 (frequency control 1:10 optional), IP55 (IP66 optional). Full detail in the STAHL ST chain hoist brochure and datasheet (see Datasheets).
| Item | Standard | Optional |
|---|---|---|
| Ambient temperature | -20 °C to +40 °C | Up to +80 °C |
| Protection (EN 60529) | IP55 | IP66 |
| Paint | Greyish black / yellow-green RAL 7021/6018, 60 to 80 µm polyurethane | Any RAL colour, 120 to 240 µm epoxy-resin base |
| Control pendant | With EMERGENCY STOP, 2-step buttons, IP65 | Magnetek radio (pushbutton or joystick), RadioMOVEit |
| Control | Contactor control including main contactor | Crane manufacturer's control without main contactor and transformer; direct control (ST 05 to ST 20) |
| Hoist motor control | Pole-changing, ratio 1:4 | Frequency controlled, ratio 1:10 |
| Travel speed (50 Hz) | 20 m/min | 2.5/10 up to 10/40 m/min; 4 to 40 m/min frequency controlled |
| Supply voltage (50 Hz) | 380 to 415 V (ST 05 also 380 to 400 V or 415 V) | All voltages |
| Load chain | Grade 8 to DIN 5684, galvanised, safety factor 5 or more | Stainless steel or blackened manganese-phosphated |
| Chain guide | Grey cast iron EN GJS | Sandwich guide of hardened spring steel plates |
| Load lifting | Load hook in bottom hook block | Thread bar, VAGH safety hook, galvanised or stainless hook |
| Limit switches | Not included | Operational hoist limit switch; gear-type limit switch; travel limit switch |
| Overload cut-off | Slipping clutch | Load sensor; SMC Multicontroller or safety PLC |
| Hoist brake | Monodisc spring-loaded brake, asbestos-free lining | Manual brake release; bypass brake; double brake |
| Signals and display | Not included | Horn, flashing light; SLD large-format load display |
| Panel box | Plastic | Sheet steel or stainless steel (ST 10 to ST 60) |
View on this page or download.
Always read the manufacturer’s instructions before use. See the documents
| Version | Hook layout | How it is used |
|---|---|---|
| Stationary ›Z‹ | One hook either side of the hoist | Adapted to the width of the load and rigidly mounted on a substructure |
| Stationary ›E‹ | Both hooks on one side of the hoist | Rigidly mounted where space is only available on one side |
| With electric trolley | Z or E layout | Becomes mobile on a monorail or crane |
| STD Vario | Electrically adjustable hook spacing | Loads of different lengths; hooks cannot shift accidentally during lifting or travel |
| STB Big Bag | Free distance between hoist and hook | Special variant for big bags up to 3,200 kg (see the STB) |
For three, four or more pick-up points, STAHL mechanically couples chain hoists with synchronous, redundant chain drives, and single-fall load monitoring is available. A vibration damper for STD 10 to STD 60 reduces the vibration passed from the chain sprocket to the load chain (the polygon effect), and an FMD1 slipping clutch test device is optionally available.
The patented chain guide is solid cast iron, and the anchorage and load-bearing parts are built into it. The hoist hangs directly from this casting, so the load is carried at the point where it engages and the force does not pass through the housing.
The case-hardened chain sprocket works with optimised return sheaves for low chain wear, and the overmounted shaft bearing means the sprocket can be inspected and replaced simply.
Powerful hoisting motors with a high duty cycle and number of starts, fan-cooled as standard. The asbestos-free electromagnetic disc brake has an oversized braking torque, is fully enclosed against humidity, vapour and dust, and its pad condition can be checked and measured.
On ST 10 to ST 60 the overload slipping clutch runs in the oil bath of an oversized helical gearbox and is adjustable from outside, so no electronic limiting is needed.
Grade 8 load chain to DIN 5684, surface-hardened, galvanised and generously sized, with a safety factor of at least 5. Stainless steel or blackened manganese-phosphated chain is available.
Chain boxes come in plastic as standard, or sheet steel, textile or stainless steel.
A: Use the enquiry button with your load, lift height, power supply and, if the hoist travels, your beam or crane details. We will come back to you with a quote and an estimated lead time.
A: The load weight and length, where it needs picking up, the lift height, and whether the hoist is fixed or travels on a runway.
A: On the STD Vario it is adjustable electrically. On the fixed Z and E versions it is set when the hoist is built.
A: Yes. Both hooks are driven by one motor through synchronised chains, so they stay level even with uneven loading.








Loading your basket…
Delivery calculated at checkout.
CheckoutCard, Apple Pay, Pay by bank, proforma or 30-day account
STAHL CraneSystems makes wire rope hoists, chain hoists, winches and crane components in Künzelsau, Germany. The business traces back to a workshop founded in Stuttgart in 1876 and is known for explosion-protected lifting equipment. It has been part of Columbus McKinnon (CMCO) since 2017.
See all STAHL products →