The STAHL CraneSystems ST05 is the smallest frame in the STAHL ST electric chain hoist programme, offered here from 125 kg to 500 kg.
For 500 kg to 1,000 kg, the ST10 is the next frame up. It suits workshop, maintenance and light production lifting, and is built to your choice of capacity, speed, suspension and lift height.
The 125 kg build is classified M6, a high duty group for repetitive cycling. Every build has two lifting speeds, slipping clutch overload protection and an IP55 enclosure as standard.
Choose a size above to see its specifications.
| Capacity | Hoist type | Falls | Lifting speed | Motor | Duty (%ED) | Starts/hour | ISO group |
|---|---|---|---|---|---|---|---|
| 125 kg | ST 0501-8/2 | 1 | 8 / 2 m/min | 0.2 / 0.05 kW | 35 / 15 | 240 / 480 | M6 |
| 250 kg | ST 0502-8/2 | 1 | 8 / 2 m/min | 0.4 / 0.1 kW | 35 / 15 | 120 / 240 | M4 |
| 500 kg | ST 0502-8/2 | 2 | 4 / 1 m/min | 0.4 / 0.1 kW | 35 / 15 | 120 / 240 | M4 |
Supply 380 to 400 V, 50 Hz three-phase. Control voltage 48 V AC. Enclosure IP55 (IP66 optional); pendant IP65. Lift heights 3, 4, 5, 6, 8 and 10 m. Trolley flange range 42 to 180 mm (push trolley), 58 to 300 mm (electric trolley). Standard paint RAL 6018 yellow-green and RAL 7021 greyish black. Made by STAHL CraneSystems GmbH (Columbus McKinnon group) under an ISO 9001 quality system; CE marked.
Each hoist is built to the configuration you select and comes with:
Options to ask about when ordering: a top hook limit switch (cut-off), and radio remote control in place of the pendant.
View on this page or download.
Always read the manufacturer’s instructions before use. See the documents
An electric motor drives a chain wheel that winds the load chain up or lets it down. The motor has two speeds, so the pendant gives you a fast speed for covering the height and a slow one, a quarter as fast, for setting the load down accurately.
When the motor stops, an enclosed disc brake holds the load.
Reeving is how the chain is run. On the 125 kg and 250 kg builds the hook hangs on a single fall of chain.
On the 500 kg build the chain runs down through a bottom block and back up (two falls), so the same hoist lifts twice the load at half the speed.
The slipping clutch limits how much the hoist can pull, protecting the hoist and the structure it hangs from. The ISO group (M4, M6) is the duty rating: a higher group means the hoist is built for more lifts and longer running time.
Slack chain drops into a chain collector sized to your lift height.
| Capacity | Hoist type | Falls | Lifting speed | ISO group | Best for |
|---|---|---|---|---|---|
| 125 kg | ST 0501-8/2 | 1 | 8 / 2 m/min | M6 | Light, repetitive lifting on production lines |
| 250 kg | ST 0502-8/2 | 1 | 8 / 2 m/min | M4 | General workshop and maintenance lifting |
| 500 kg | ST 0502-8/2 | 2 | 4 / 1 m/min | M4 | Heavier loads where slower, finer positioning helps |
Then choose the suspension: a hook for a fixed position, a push trolley to move it along a beam by hand, or an electric trolley (20 m/min, or two-speed 20/5 m/min) to travel under power. The push trolley suits runway flanges from 42 to 180 mm and the electric trolley 58 to 300 mm, so confirm your beam flange width when ordering.
Lift heights from 3 m to 10 m can be selected online (up to 6 m on the 500 kg build); longer lifts are quoted on request.
A: A three-phase 380 to 400 V, 50 Hz supply. The pendant runs on a 48 V AC control circuit.
A: The standard build is 3 m, and up to 10 m can be selected online (6 m on the 500 kg build). STAHL lists hook paths for the ST05 of up to 24 m on a single fall or 12 m on two falls with the right chain collector, so contact us for a longer lift.
A: No. A chain collector sized to your lift height is included with every configuration.
A: The push trolley suits runway flange widths from 42 to 180 mm and the electric trolley 58 to 300 mm. Give us your beam flange width when you order.
A: The ST05 operational limit switch cuts off at the top hook position only. A gear limit switch, which can cut off at both the top and bottom hook positions, is available as an option and needs contactor control. Ask us to confirm for your build.

Loading your basket…
Delivery calculated at checkout.
CheckoutCard, Apple Pay, Pay by bank, proforma or 30-day account
STAHL CraneSystems makes wire rope hoists, chain hoists, winches and crane components in Künzelsau, Germany. The business traces back to a workshop founded in Stuttgart in 1876 and is known for explosion-protected lifting equipment. It has been part of Columbus McKinnon (CMCO) since 2017.
See all STAHL products →