The STAHL CraneSystems ST30 is the M3 duty frame in the heavy end of the STAHL ST electric chain hoist programme, offered here at 1,600 kg and 3,200 kg.
It suits intermittent or occasional lifting of significant loads, where the cycle count is low.
Two-speed lifting, slipping clutch overload protection and an IP55 enclosure are standard. Where the same loads are lifted frequently through the shift, choose the M5-rated ST32 instead.
Choose a size above to see its specifications.
| Capacity | Hoist type | Falls | Lifting speed | Motor | Duty (%ED) | Starts/hour | ISO group |
|---|---|---|---|---|---|---|---|
| 1,600 kg | ST 3016-8/2 | 1 | 8 / 2 m/min | 2.3 / 0.57 kW | 40 / 20 | 120 / 240 | M3 |
| 3,200 kg | ST 3016-8/2 | 2 | 4 / 1 m/min | 2.3 / 0.57 kW | 40 / 20 | 120 / 240 | M3 |
Supply 380 to 415 V, 50 Hz three-phase. Control voltage 48 V AC. Enclosure IP55; pendant IP65. Lift heights 3, 4, 5, 6, 8 and 10 m online; STAHL lists hook paths up to 30 m on a single fall or 15 m on two falls, depending on the chain collector. Trolley flange range 66 to 300 mm. Made by STAHL CraneSystems GmbH (Columbus McKinnon group) under an ISO 9001 quality system; CE marked.
Each hoist is built to the configuration you select and comes with:
For loads up to 2,000 kg, there is the ST20.
View on this page or download.
Always read the manufacturer’s instructions before use. See the documents
An electric motor drives a chain wheel that winds the load chain. The pendant gives a fast speed for covering the height and a creep speed, a quarter as fast, for setting the load down accurately.
A brake holds the load when the motor stops.
On the lower capacity the hook hangs on a single fall of chain; on the higher capacity the chain runs down through a bottom block and back up (two falls), lifting twice the load at half the speed. The slipping clutch limits how hard the hoist can pull, protecting it and the structure.
The ISO group (M3, M4, M5) is the duty rating: higher means more lifts and longer running time.
| Capacity | Hoist type | Falls | Lifting speed | ISO group | Best for |
|---|---|---|---|---|---|
| 1,600 kg | ST 3016-8/2 | 1 | 8 / 2 m/min | M3 | Occasional heavy lifts at standard speed |
| 3,200 kg | ST 3016-8/2 | 2 | 4 / 1 m/min | M3 | Occasional lifts of the heaviest loads |
Then choose the suspension: a hook for a fixed position, a push trolley to move along a beam by hand, or an electric trolley (20 m/min, or two-speed 20/5 m/min). Trolleys suit runway flanges 66 to 300 mm, so confirm your beam flange width when ordering.
Lift heights from 3 m to 10 m can be selected online; longer lifts are quoted on request.
A: Three-phase 380 to 415 V, 50 Hz. The pendant runs on a 48 V AC control circuit.
A: Up to 10 m can be selected online. STAHL lists hook paths for the ST30 of up to 30 m on a single fall or 15 m on two falls with the right chain collector, so contact us for a longer lift.
A: No. A collector sized to your lift height is included with every configuration.
A: Both a top hook cut-off and a combined top and bottom cut-off are available, plus slow-down and stop travel limits for powered trolleys.

Loading your basket…
Delivery calculated at checkout.
CheckoutCard, Apple Pay, Pay by bank, proforma or 30-day account
STAHL CraneSystems makes wire rope hoists, chain hoists, winches and crane components in Künzelsau, Germany. The business traces back to a workshop founded in Stuttgart in 1876 and is known for explosion-protected lifting equipment. It has been part of Columbus McKinnon (CMCO) since 2017.
See all STAHL products →